2.2.15.24. Check of bolts
|
Fig. 2.171. Measurement of length of a bolt
|
Measure length of each bolt (fig. 2.171).
Replace all bolts which length exceeds maximum.
Length is L
- 1. Operation and maintenance of the car
- 2. Engine
- 2.1. General description of new engines of the L8, LF and L3 models
- 2.2. Mechanical part of engines
- 2.2.1. Engines of the L8 and LF models
- 2.2.2. Verification of the contents of CO/CH in the fulfilled gases
- 2.2.3. Measurement of a compression in engine cylinders
- 2.2.4. Check of a belt of the drive of auxiliary units
- 2.2.5. General information and safety measures at removal of the power unit
- 2.2.6. Removal of sealant
- 2.2.7. Removal and installation of the power unit
- 2.2.8. Check of the executive mechanism of change of phases of gas distribution (L3)
- 2.2.9. Removal and installation of the executive mechanism of change of phases of gas distribution (L3)
- 2.2.10. Gas distribution mechanism drive chain
- 2.2.11. Removal and installation of the operating oil valve (OCV) (L3)
- 2.2.12. Check of the operating oil valve (OCV) (L3)
- 2.2.13. Check of operation of the spool-type valve (OCV) (L3)
- 2.2.14. The general repair operations on the power unit
- 2.2.15. Check of a head of the block of cylinders
- 2.2.15.1. Check of the directing valve plug
- 2.2.15.2. Measurement of length of the valve
- 2.2.15.3. Measurement of diameter of a core of the valve
- 2.2.15.4. Measurement of internal diameter of the directing valve plug
- 2.2.15.5. Measurement of height of a vystupaniye of the directing valve plug
- 2.2.15.6. Replacement of the directing valve plug
- 2.2.15.7. A press fitting of the directing valve plug
- 2.2.15.8. Check and repair of a saddle of the valve
- 2.2.15.9. Check of a valvate spring
- 2.2.15.10. Check of a cam-shaft
- 2.2.15.11. Measurement of diameter of a neck of a cam-shaft
- 2.2.15.12. Measurement of a radial gap of a neck of a cam-shaft
- 2.2.15.13. Measurement of an axial gap of a neck of a cam-shaft
- 2.2.15.14. Check of a pusher of the valve
- 2.2.15.15. Check of the block of cylinders
- 2.2.15.16. Valve check of a maslorazbryzgivayushchy nozzle
- 2.2.15.17. Check of the piston
- 2.2.15.18. Check of a bent shaft
- 2.2.15.19. Measurement of size of a beating of a bent shaft
- 2.2.15.20. Measurement of diameters of necks of a bent shaft
- 2.2.15.21. Measurement of a radial gap in radical bearings of a bent shaft
- 2.2.15.22. Check of a side gap of a rod
- 2.2.15.23. Measurement of a radial gap of a rod
- 2.2.15.24. Check of bolts
- 2.2.16. Assembly of the block of cylinders (beginning)
- 2.2.17. Assembly of the block of cylinders (termination)
- 2.2.18. Assembly of a head of the block of cylinders
- 2.2.19. Assembly of the drive of the mechanism of gas distribution
- 2.3. Appendix 1
- 2.4. Appendix 2
- 2.5. Appendix 3
- 2.6. The Z6 engine – a mechanical part
- 2.7. Lubrication system
- 2.8. Cooling system
- 2.9. System of an admission
- 2.10. Fuel system
- 2.11. System of production of the fulfilled gases and system of decrease in toxicity
- 2.12. System of ignition
- 2.13. Control system
- 2.14. Tables
- 3. Transmission
- 4. Running gear
- 5. Steering mechanism
- 6. Brake system
- 7. Onboard electric equipment
- 8. Body
